WPA2 key reinstallation attack (KRACK) does not affect LigoPTMP
What’s new in LigoPTMP 7.55-1 firmware release
New:
- Added discovery services configuration
- Added data VLAN on Slave configuration
Fixes:
- Fixed issue when LigoSU does not show IP with management VLAN
- Fixed LigoSU device Management from LigoBase
v7.55 (LigoPTMP)
New:
- Added multicast echo control on Master
- Added smart channel width on Slave
- Improved Slave devices upgrade mechanism
- Slave statistics now are saved after reboot
Fixes:
- Fixed 10s delay on GUI when changing transmit power
- Fixed password validation
v7.3 (LigoPTMP)
Initial Release
New:
- Added Configuration test, discard and save & apply buttons
- Added Password change
- Added Reboot device via UI
- Added Backup/Restore device configuration
- Added Reset to factory defaults via UI
- Added Troubleshooting file generation
- Added SFTP support
- Added Firmware upgrade
- Added System log
- Added Firmware upgrade checking
- Added “Dual-Boot” mode
- Added “Recovery” mode
- Added Device settings Friendly name, Device location, Device coordinates, Contact information, Height above ground level
- Added Product File upgrade via firmware upgrade
- Added Jumbo frame support
- Added Linktest tool
- Added serial console access via Wi-Fi and web terminal on BS
- Added LEDs functionality: reset to defaults, firmware upgrade, booting, active management radio
- Added QOS functionality (Strict and WRR)
- Added Remote device Firmware upgrade option
- Added Configuration wizard
- Added Remote device configuration functionality
- Added LEDs control via GUI
- Added Ethernet ports configuration
- Added STP control
- Added Radars scanning indication CAC
- Added Traffic limitation option
- Added in Maintenance Dual boot images selection
- Added option to generate configuration file for Slave device and for whole network
- Added spectrum analyzer
- Added option to disable reset button
- Added SNMP support in GUI
- Added in Maintenance firmware upgrade, configuration backup and restore, reboot, reset to defaults options
- Added Syslog and Troubleshooting file support
- Added Site Survey
- Added Disable broadcast link ID option
- Added Antenna alignment
- Added in Settings NTP client
- Added in Settings system security options
- Added in Settings system characterization options
- Added in Setting system advanced settings: ETH2 port control, PoE on ETH2 port control, Public status page
- Added in Services WNMS agent options
- Added in Services Wireless management interface options
- Added in Services Management options: SSH, HTTP server control
- Added in statistics Signal level graph
- Added in statistics Instant traffic throughput and PPS graphs
- Added in statistics Wireless clients table
- Added in Status statistics Radio and Ethernet MAC representation
- Added in Status statistics Radio peer MAC representation
- Added in Status statistics ETH1, ETH2, Wireless TX/RX data bytes counters
- Added in Status statistics ETH1, ETH2, Wireless TX/RX error counters
- Added in Status statistics Wireless TX/RX frames counters
- Added device discovery option in core
- Added in status information Network settings
- Added in status information Wireless signal level in dBm
- Added in status information Link ID, Frequency, Channel width, Device, link uptime, distance, tx power, tx/rx data rate, noise level, signal local and remote level
- Added in status information Product model, name, serial number, FW version, uptime, friendly name, device location, Channel width
- Added in status information Latitude/Longitude, Height, Operating mode, Noise level, TX power, MAX TX data rate, Antenna Gain
- Added Link quality display in GUI
- Added in status Ethernet networks state and speed
- Added multiple countries support in product file
- Added System date and time configuration
- Added Wireless connection status
- Added IPv6 support
- Added IPv4 support
- Added Management VLAN
- Added IP fallback settings on DHCP client
- Added Radio/Link security phrase generation
- Added Encryption WPA2/AES
- Added Regulatory DB support
- Added set SSID
- Added search SSID function
- Added Status page public access
- Added auto data rate
- Added Log in page and language selection
- Added 5/10/20/40/80 MHz wireless channel width support
- Added SISO/MIMO mode in core
- Added AMSDU in core
- Added WMM in core
- Added Fragmentation parameter in core
- Added CT country code
- Added “Operational Country” support
- Added DFS control
- Added Auto channel
- Added Master mode
- Added Slave mode
- Added support for “Reset button” reset to factory defaults
- Added User Agreement